Proline motorsport abs removal

[Liamc111]

Has anyone fitted one of their kits? Looking to fit mine next weekend and just trying to get an idea of which line goes where before I start pulling th car apart. Fyi this is to also fit a bias valve also.

 

[Nas80]

They didn't provide a diagram?

 

[Liamc111]

Nope, just a bag of brake lines

 

[jack.am]

Nope, just a bag of brake lines

Lol. Nice.

They look a bit on the long side. It's been a while since I did mine but I imagine the tee-piece section will be the fronts, the two little ones from the master cylinder to the stock bias valve and the long one to the rears?

 

[bash]

Nope, just a bag of brake lines

Ugh. Was about to pull the trigger on one of these kits. No instructions? That's pretty shitebag. How did you get on?

 

[Liamc111]

Well all the original lines are out and once the new ones were laid next to them it 'should' be pretty straight forward. Planning to go and Start fitting tomorrow so will let you know

 

[Lsxphil]

Let us know how you get on as i have not fitted mine yet either.

 

[Liamc111]

Had another look today and struggling to find a routing. I have messaged proline on fb asking if they have any fitted photos from another car or fitting diagram for which length line goes where...still waiting for a response

 

[noyzboy]

Had another look today and struggling to find a routing. I have messaged proline on fb asking if they have any fitted photos from another car or fitting diagram for which length line goes where...still waiting for a response

Can you still get that through a MOT ??

 

[Greg87]

Can you still get that through a MOT ??

I done an abs removal on an old car I had.
MOT was fine, you just have to remove all traces of the system so there is technically nothing missing.

 

[jack.am]

ABS should be the least of your worries on MOT time...

 

[bash]

Had another look today and struggling to find a routing. I have messaged proline on fb asking if they have any fitted photos from another car or fitting diagram for which length line goes where...still waiting for a response

Any update on this Liam? Also, did you go for the standard externally ran kit or the internal one?

 

[bash]

Well I have an update of my own. Ordered the kit 6 days ago, got an email saying it had been dispatched now the dude tells me everything is made to order and mine is in a queue of a bunch of orders. Looked at the negative comments on ebay and they all say the same thing. His attitude seemed bad also. I shall give him a call tomorrow and take it from there but my advice for anyone else looking to order this kit is avoid.

 

[Liamc111]

Sorry for no reply bash, only just decided to take one last look again today, still cant find a happy routing and no replies from them too. Starting to think about sacking it of and just making some hardlines up so I'm happy with the routing.
Hate to say it but another unhappy customer here as well

 

[Lsxphil]

Sorry for no reply bash, only just decided to take one last look again today, still cant find a happy routing and no replies from them too. Starting to think about sacking it of and just making some hardlines up so I'm happy with the routing.
Hate to say it but another unhappy customer here as well

I have a set that are not through the cabin. Aren’t they surposed to run under the car to the rear subframe? Or have I missed something.

 

[Liamc111]

I've got the stock location lines too which should run the same route as oem...they don't.

 

[bash]

I decided to ask for a refund through ebay. I was told i'd bumped to the front of the queue which I highly doubt but got the refund regardless. I'm going to take some measurements and design some myself. Probably just utilise the existing hard lines for the rear and then plumb the rest up with braided

 

[Nas80]

You know it's far easier and cheaper to do it in kunifer.

I've done this job a couple of times now it's actually pretty easy

 

[Liamc111]

Found these pictures of of a rhd car in the us which might be of some help @bash

 

[bash]

Thanks for this Liam. This is why im gonna use braided though. The bends here are all over the place and for me will run too close to the turbo on the BMC side.